JohnnyCheese
- Thread starter 1313R
- Start date
Purplehaze
Registered
what other mods have you done (i.e) pistons, cams, headwork, modded airbox etc because it'll make a differance. I believe that BDE Hindle pipe will make more power with a built motor.
Johnnycheese
Registered
Stock motor Muzzy best bang for the buck.
Or HMF bigbird,BDE3.
Buildt motor
HMF-BDE-Akro($$$$$)
Or HMF bigbird,BDE3.
Buildt motor
HMF-BDE-Akro($$$$$)
1313R
Registered
All stock. Just lowered in the rear and tubbed. I have a 16tooth front sprocket. Haven't installed it yet waiting to get a new chain first. He has a custom mapp full hindle exhaust and it's lowered in the rear. Strapped in the front, with different gears. I run 6.70's and he usually runs 6.50's or mid 6.40's. 60ft times are almost identical, but at the 330ft mark he starts pullin away. I just want to keep up or blow bye him. What do you recommend?
Brock Gen 3 Hindle and a sprocket, dude. Trust me, the BDE exhaust is soooooooo friggin' schweet!
I bought a Muzzy Ti Oval from Johnny Cheese for only $750 - it looks great, sounds great and the Muzzy, Hindle and Akra make within 1-3 hp of each other according to Johnny. If you buy a Muzzy oval in Aluminium it would cost even less. They are all good systems - depends on how you want it to look and how much you want to spend. Bullet Train has great pictures of his system and install titled "all the pretty horses" - check it out - he had his system polished and it looks awesome. I like more of an understated look so I went with flat Titanium - I like the way it looks and it will be easy to take care of.
When you install your system - a fun and easy project - remove the PAIR valve while you have your bike apart - you can buy a block off kit from Brock "BDE" or Muzzy.
Good Luck!
When you install your system - a fun and easy project - remove the PAIR valve while you have your bike apart - you can buy a block off kit from Brock "BDE" or Muzzy.
Good Luck!
Hmmm...Do you know how he's geared...I'll bet he went up in the rear...If I were you I'ld go 16/42...He want pull you then...That setup will go with the stock length chain...Then your choice of exhaust want be that big of a deal...I'm running a Muzzy stainless header alum can right now...My friend installed a Hindle on his 12 and I still eat his a$$ on the regular...We had about a $400 price difference in my favor on the systems...
1313R,
You should be able to run with your buddy now! How much do you weight?
You just need to practice your launch. Get that clutch out quicker and gas on faster! You can run 6.40's with the setup you have now.
As for the pipe, I have and recommend the BDE Gen III!
If you're only in second gear "on the big end" then you're losing because he's shifting and you're not. Hehehehehehehe......It would be closer if I wasn't spinning second gear on the big end. I will work on it. Thanks for the info guys.
1313R
Registered
Oh yeah and it spins what little of third gets used. Thanks for bringing that to my attention BT. :tounge: We're only running the 1/8th mile just in case you didn't realize it. But if I were running 6.70"s in the 1/4 I'd be quite pleased. Thanks for the vote of confedence.
<!--EDIT|1313R
Reason for Edit: None given...|1069092781 -->
<!--EDIT|1313R
Reason for Edit: None given...|1069092781 -->
Just havin' a little fun there dude.Oh yeah and it spins what little of third gets used. Thanks for bringing that to my attention BT. :tounge: We're only running the 1/8th mile just in case you didn't realize it. But if I were running 6.70"s in the 1/4 I'd be quite pleased. Thanks for the vote of confedence.
Similar threads
