Online motorcycle stores. Can someone help me out??

[OB_X-treme]

I want to buy a D&D slip-on for my R6. At my local yamaha dealership he said he would give it to me for $460(CDN) is there any place online or companys in the states that would give me a better deal?

Thanks for any help,
Steve

[OB_BUSA00021]

Try mawonline.com.I have purchased several items from them and have had no problems.They should easily beat dealer prices.

[OB_rchh]

try starcycle they should be able to hook you up. 800-990-2453/ they advertise nobody beats are prices. good luck

[OB_Oger]

Try Cycle stuff, they will definetly beat anyones price.

[OB_Factory]

Check kneedraggers.com - Good helmet prices.

Also, check the back of the Motorcyclist and Cycle World magazines - just call around. That's how I do most of my shopping once I know what I want.

[This message has been edited by Factory (edited 11 May 2000).]

[OB_00 so Blue]

http://cybercyclestuff.com/index2.htm

[OB_Juanski]

Try www.bikeyard.com and ask them to find you a good used slip-on for your bike on their satellite hotline.

[OB_Hooshy Bushy]

I DO NOT recommend: Competition Accessories (www.compacc.com)

I've gotten piss-poor service the last several orders I've made with them.

[OB_Blue2Busa]

Judge, I may be wrong but I think the reason you like the prices at Keirnan's Is becaue it is an old site, The newest bike year I can find for anything is a 1998. Maybe I am not working the site correctly.

[Guest]

I've been to these. Keirnan's and MAWONLINE seem to have the best prices.

http://www.braincell.com/kiernan/
http://www.accwhse.com/
http://www.motorcyclemart.com/ (Cruisers)
http://www.motodepot.com/
http://www.mawonline.com/

This link is real helpful, has ton's of links.

http://elwood.pionet.net/~oneal/cycles.htm

Bob'98ZX11

[Bruce Bohannon]

Bob, The MOTORHEAD is dead on with what he is telling you.
Assumes - near sea level...
Shims are 50 cents.... Jet kit is 100 bucks. Labor is same. Tell your guy to go your way. Your the customer, Or, get a manual - it's fun!

[OB_Johnnycheese]

Don't forget float level VERY important on ram air carb bikes
I always used a Vance and Hines Igniton adv.
5 degrees.clean up the bottom nice.
Please don't get me started on ZX11's that is how Motorhead and I started talking.

[OB_Johnnycheese]

also bob it will say with the factory kit to use stock main jets.
of all the Factroy jet kits the one for the ZX11 I refuse to install I have done 3 of them and all three customers had me do it with shims and jets and all three are getting around the 40-50 mpg with or with out stock exhaust.There is also a trick you need to do with the slide springs.

[Guest]

Blue,

You're absolutley right, their site needs to be updated. I just ordered a pipe and jet kit from them and I had to double check the Factory jet kit to make sure it would work on my '98 ZX11. Their site said the Config 10 jet kit was for '93-96 "D" model ZX11's. No changes were made to the carburation on the ZX11 from '96 -'99 (that I'm aware of) so I ordered it? Double checked with Factory as well.

Bob

[OB_THE MOTORHEAD]

bob you could shim you needles 2mm back out your pilots 3 1/2 turns and go up 1 size on the mains and get the same results.keep the inboard outboard spread though

[Guest]

TMH,

Thanks for the heads up, I've actually heard of this on the ZX11-ZX12 boards. Unfortunately I don't do much maintenance to my bike other than oil/filter and chain lube/adjust. Everything else goes to the shop. I'll ask him if this is viable. It's not that I don't trust your opinion, it's just he's doing the work so I'll probably have to go "his way".

Thanks again..

Bob