billyjob007
Registered
How to jack up gen 2 with extended 360 single side swing arm
this is what you need, but search for them in your own countryCentral Lift compatibel met Suzuki Hayabusa GSX-R 1300 08-24 zwarte Paddock Stand ConStands Power-Classic
Complete set inclusief model-specifieke adapterplaat Central Paddock Stand voor snel en eenvoudig opvijzelen van de machine 4 dubbele zwenkwielen voor eenvoudig manoeuvreren Afmetingen: lengte 78 cm / breedte 54 cm / hoogte 75,5 cm Maximaal draagvermogen 300 kg bij 17 kg eigen gewicht Ideaal...www.motea.com
this is what you need, but search for them in your own countryCentral Lift compatibel met Suzuki Hayabusa GSX-R 1300 08-24 zwarte Paddock Stand ConStands Power-Classic
Complete set inclusief model-specifieke adapterplaat Central Paddock Stand voor snel en eenvoudig opvijzelen van de machine 4 dubbele zwenkwielen voor eenvoudig manoeuvreren Afmetingen: lengte 78 cm / breedte 54 cm / hoogte 75,5 cm Maximaal draagvermogen 300 kg bij 17 kg eigen gewicht Ideaal...www.motea.com
They don’t ship to USA and I can’t find one here for saleCentral Lift compatibel met Suzuki Hayabusa GSX-R 1300 08-24 zwarte Paddock Stand ConStands Power-Classic
Complete set inclusief model-specifieke adapterplaat Central Paddock Stand voor snel en eenvoudig opvijzelen van de machine 4 dubbele zwenkwielen voor eenvoudig manoeuvreren Afmetingen: lengte 78 cm / breedte 54 cm / hoogte 75,5 cm Maximaal draagvermogen 300 kg bij 17 kg eigen gewicht Ideaal...www.motea.com
this is what you need, but search for them in your own country
I don’t have any extra hand jest my wifeI have a Bursig stand, and they work great, but, you don't need one.
Get a roughly 3' long round steel bar in 13/16", 21mm in diameter.
Run it through the lower frame hole.
If the front wheel is in a chock, or on a front forklift/triple clamp stand, and you have a couple extra hands, you can lift the rear, and set each side's protruding bar down on to a jackstand on each side.
It's awkward with the fat tire, but doable.
I don’t have any extra hand jest my wife
I have a Bursig stand, and they work great, but, you don't need one.
Get a roughly 3' long round steel bar in 13/16", 21mm in diameter.
Run it through the lower frame hole.
If the front wheel is in a chock, or on a front forklift/triple clamp stand, and you have a couple extra hands, you can lift the rear, and set each side's protruding bar down on to a jackstand on each side.
It's awkward with the fat tire, but doable.
How to jack up gen 2 with extended 360 single side swing arm
Nice!
Nicejepp
4 shure
but not that handy to transport
(i´m thinking about how to build it foldable)
so i store it in my garage for every busa i get for maintenance etc.
and when ever a busa comes in
i put it on my bench with that selfmade mid jack.
the only job that is impossible to do is the pulling of the swingarm.
thatfor i have a swiveling double-t-steelbeam under the ceiling + a 500 kg chain hoist to lift busa´s ass
see my yt-video of the engine mounting at a busa
or see my lil garage walk around also as a 2nd yt-video