Installation ABS on the K9
- Thread starter Diamond
- Start date
lease:
I think you are pulling a Star Trek on this one buddy. You are where no man has gone before. All I can do is wish you luck! 
I suppose you can matchup an 09 and whatever year ABS you have wiring diagrams and see if you can find everything you need for the abs. on the sensor side you probably only need engine RPMs. But control side that's a major nightmare. Still however, I'm sure they didn't re-invent the wheel so it's probably possible if you are clever enough. I looked into this and decided it was cheaper to take everything off my 09, sell it, then buy an ABS 13 and start all over.
Someone will chime in soon........
Tony Nitrous
Registered
Not looked at the Busa but the B-King came out with and without ABS a while back.
One guy looked into fitting it and when he found out the amount of stuff he'd need
he soon gave in!
One guy looked into fitting it and when he found out the amount of stuff he'd need
he soon gave in!
Tony Nitrous
Registered
What do you call "all" ?
Hoses, wiring loom, wheel sensor plates and pick ups,
how much electrics are involved or different from the non-ABS version?
No reason it can't be done if you swap enough parts!
Hoses, wiring loom, wheel sensor plates and pick ups,
how much electrics are involved or different from the non-ABS version?
No reason it can't be done if you swap enough parts!
Im thinking it would be easiest to replace the entire engine management system with the ABS version.
Tony Nitrous
Registered
Diamond, your doing fine, if English isn't your natural tongue.
Good luck with the conversion,
I admit its not something I'd do,
I'd buy an ABS bike a swap over any worthwhile parts I wanted.
I'd be very interested to hear how you get on.
It's not something I'm familiar with.
I look forward to some updates.
Good luck!
Tony
Good luck with the conversion,
I admit its not something I'd do,
I'd buy an ABS bike a swap over any worthwhile parts I wanted.
I'd be very interested to hear how you get on.
It's not something I'm familiar with.
I look forward to some updates.
Good luck!
Tony
I have every thing off of my 2013,
except the rear hard lines, i had to cut them to remove them from the bike.
I am also planing on swapping the harness on the bike, but have not done that yet.
So if you can wait, till i swap the harness, i will have the following for sale
ABS pump
Front lines, the hard as well as the flex lines
Front ABS sensor
Rear ABS sensor
Part of the rear lines, {not sure what was cut, the input or the ouput?}
Complete 2013 harness.
Other things you will need
Wheels to accept the speed sensor rings
Possible Gauge cluster, it does have an indicator light in it.
Rear lines either made up or OEM
Let me know if you are interested, and ill take pics!
John
except the rear hard lines, i had to cut them to remove them from the bike.
I am also planing on swapping the harness on the bike, but have not done that yet.
So if you can wait, till i swap the harness, i will have the following for sale
ABS pump
Front lines, the hard as well as the flex lines
Front ABS sensor
Rear ABS sensor
Part of the rear lines, {not sure what was cut, the input or the ouput?}
Complete 2013 harness.
Other things you will need
Wheels to accept the speed sensor rings
Possible Gauge cluster, it does have an indicator light in it.
Rear lines either made up or OEM
Let me know if you are interested, and ill take pics!
John
Telboy2000
Registered
impressive bit of work...well done...have you added up the final cost?...including your time and additional materials to make the wiring harness etc
That's very impressive. You need to write this up and tell us how you did this as there are a lot of people who would love to know what all was involved.
Just curious. Are you typing in Russian and the site is translating? That's awesome.
Diamond
Registered
and great work fitting the ABS :agree:Similar threads
