Recent content by liass44

  1. L

    Gen 3 Full Yosh AT2 System for SAle

    I'm selling my Full Yosh AT2 system. Has around 1000 miles on it. The bike was dropped on one side (not crashed) and left some scratches on the muffler, with most being on the replaceable heat shield which I'm sure can be ordered from Yosh. No dents or dings on the pipe or headers. 900 +...
  2. L

    Gen 3 "premium" seat

    Still for sale?
  3. L

    Gen3 Yoshimura r77 slip ons like new

    I have a full AT2 System for sale for a gen 3. Sounds excellent!!
  4. L

    Turbo Partout

    Check out my turbo busa partout https://www.hayabusa.org/forum/threads/turbo-hayabusa-partout.201136/
  5. L

    Where to mount gauges

    I have the same setup. 2 dynotune rectangle gauges like that. I put a tad bit of gorilla glue on them and they are solid as a rock... The velcro dang sure doesn't cut it.. Taking them off may be a interesting feat but I don't see any reason to for a while atleast...
  6. L

    Gen 2 turbo street bike build

    Joe, I'm in the process of building a gen2 turbo bike aswell. My goals are a little more modest (380 on pump fuel). Going to be a stage 2 ultra. Richard told me drop in headstuds would be fine, I asked about the output shaft he said not necessary. I went ahead and sent it in to robinson for some...
  7. L

    Opinions on cylinders?

    Yes Michael I know e85 is often e65. I had an ethanol content analyzer on my evo and Kroger always has the best ethanol and it’s usually only e80. I always tuned on E60 just to play it safe
  8. L

    Opinions on cylinders?

    I ended up buying a clean 8k mile gen 1 std bore block, 260 shipped!
  9. L

    Opinions on cylinders?

    Michael, Enough to get to 350rwhp on pump gas on a rcc stage 1 turbo. Will be going with the RCC ultra plenum. I have read about gen 2 blocks being prone to cracking once at 84mm. I am sending the block to USChrome to have them replate on std bore if possible. If not hopefully they can just...
  10. L

    Opinions on cylinders?

    Yes I am just going to either get it replated if possible or just have it bored up to the next size.
  11. L

    Opinions on cylinders?

    Opinions on these cylinders? Came off my 2011 turbo. The pistons were slightly melted at the top ring land between cylinders (not intake or exhaust side), I removed the small amount of piston material from the cylinder walls with acid and this is what I am working with. There is zero scoring...
  12. L

    300HP Goals Gen1

    Boosted, I left you a voicemail last night. Call me when you get a chance 972 898 3913. The bike blew the head gasket today, hoping thats it. Wanting to bring the bike down there and get some work done on it.
  13. L

    300HP Goals Gen1

    No I did not. We have communicated via email a year or two ago when I was contemplating going turbo.
  14. L

    300HP Goals Gen1

    Boosted, I sold the 06 busa yesterday and am going to mississippi tomorrow to pick up a 2011 busa with a stage 1 rcc kit. Bike is super clean and tuned by Richard at rcc. I'll probably be in touch with you in the near future to arrange plans to turn it into a 300-350hp bike.
  15. L

    300HP Goals Gen1

    How often does to meth tank have to be refilled? If I slap an ultra plenum on the bike with a second set of injectors will satisfy the cooling needs?
Back
Top