Recent content by Jeremy112113

  1. J

    2005 Service Manual?

    Could anyone point me to where I can find a DIY guide or service manual for splitting the cases for transmission repair? I have an issue with 6th gear slipping out under hard acceleration, then immediately back in so I figured it's time to get the transmission undercut and to replace anything...
  2. J

    Clutch Slipping After Oil Change?

    I went for a ride this morning, made sure the bike was to operating temps and was shifted through all gears. I tried to recreate the issue I was having and it would not recreate. I'm very excited considering now, I don't actually have to drop my motor and take out the transmission. The rpm range...
  3. J

    Clutch Slipping After Oil Change?

    Update: my new slave cylinder came in today and it definitely has a nice 'spring' to it when pressed. I flushed the line, installed the slave cylinder, filled the reservoir with new Dot4 fluid, and bled the air out of the system. Whenever I pull in the clutch now, it definitely has more of a...
  4. J

    Clutch Slipping After Oil Change?

    When my new slave cylinder comes in, I'll flush the clutch line (something I didn't do when I overhauled the m/c a couple years back) and bleed the system once back together. Thanks for the post, it really cleared up how the slave cylinder operates
  5. J

    Clutch Slipping After Oil Change?

    I measured stack height today, and four pointed 1.98 on all four points. Considering it's hard to take a picture with oily hands and a caliper, pic below for proof. The caliper does have a tolerance of +/-.01. I'm still waiting for my new slave cylinder to come in. With some research, my...
  6. J

    Clutch Slipping After Oil Change?

    Okay, I'll do this when I get home today. As mentioned, when I did overhaul my master cylinder a couple years ago, I think I may have filled the brake fluid close to the top. The fluid that was in it was gray, but I don't recall ever having the hose off (like it is now) and completely draining...
  7. J

    Clutch Slipping After Oil Change?

    I haven't done this, but considering I used to be a machinist for a couple of years, I should have a pair of these lol. My clutch cover is still off, and when my pair comes in I'll measure them.
  8. J

    Clutch Slipping After Oil Change?

    I did some searching and the slave cylinder should return and kind of go in and out whenever you pull the lever. I saw where there is a cable conversion, has anyone tried this? Seems interesting, what are everyone's thoughts?
  9. J

    Clutch Slipping After Oil Change?

    So I took the front sprocket cover off and the push rod came with it. When I squeezed the clutch the cylinder pushed out, but did not return. Is this normal? Pictures below:
  10. J

    Clutch Slipping After Oil Change?

    Okay, I'll do this in a few and report back. Thanks!
  11. J

    Clutch Slipping After Oil Change?

    Okay, this makes sense. So if the clutch is good, where else should I check? My fear is the transmission being worn and needing machined/worked. What would the symptoms be? I can't find specific symptoms for my situation.
  12. J

    Clutch Slipping After Oil Change?

    No, it doesn't say it. I checked for that when I picked it up from the store. I did check my clutch fluid revoir and it was low. Is it possible that this black soot is this fluid leaking into here somehow?
  13. J

    Clutch Slipping After Oil Change?

    So I took pictures, my clutch looks good but there is black soot on the inside (pictured) if it isn't my clutch, would it probably be my transmission?
  14. J

    Clutch Slipping After Oil Change?

    Yeah, I figured lol, I'll pull the clutch and post pics tonight
  15. J

    Clutch Slipping After Oil Change?

    At most 3500 miles. I changed it earlier in 2018
Back
Top