Recent content by gregsbusa

  1. G

    need some help please

    I have a gen 2 and I think I have some play in the swingarm, when I lift the rear off the ground with a rod through the swingarm pivot sitting on jackstands, I can grab the rear wheel and pull it to the clutch side of the bike and see the entire swingarm move about .25 of an inch. I took it in...
  2. G

    Swingarm Play?

    pulls straight, just the front end is wandering all over the place, did everything up front, the swingarm was the last thing checked.
  3. G

    Swingarm Play?

    5/8 rod through swingarm pivot bolt on jackstands is how its off the ground, its never been off the bike, never wrecked, has 9k miles on it.
  4. G

    Swingarm Play?

    Well thanks for the brake help, now next problem. With the rear end off the ground, I can grab the rear wheel and pull toward the clutch side of the bike and I can see the swingarm move about 1/4in. The wheel bearings are fine, I can actually see the singarm move, I did check all fastners and...
  5. G

    Brake Question?

    I lifted the front end up lastnight and noticed when I spun the wheel the brakes would grab about 1/4 of the rotor and the other 3/4 spun ok. I took the calipers off and spun the wheel but cant see that the rotor is warped. The brake pads look fine, even wear on all pads, so I dont think a...
  6. G

    Front Suspension

    Eric at Computrack, its in Pompano Beach, FL. Go to Racetech's website and u can find there info. They are a licensed Racetech shop.
  7. G

    About fed up with this bike!

    I am turning to the forum for some help. I have an 08 that has 9k miles on it. My problem is that since I trailered the bike down to Miami and back about 9 months and 3000miles ago the bike has never felt the same. Another guy on here had the same problem, but ended up trading his in. I am...
  8. G

    how to remove gen II front axel

    I loosen the 2 left(when looking at the front end) pinch bolts, remove the axle bolt, then remove the other 2 pinch bolts, the last 2 pinch bolts hold the axle for bolt removal, once bolt is out, axle should slide right out with your fingers.
  9. G

    tools needed

    Where is the best place to pick up some tools so I can perform some steering head bearing maintance, I've been searching but can find anywhere to get the specialty sockets needed for the steering nuts.
  10. G

    Genii

    Suzuki isnt producing any 2010's because of so many dealers going out of business, they have slowed production way down.
  11. G

    Where did the gen 2 shop manual go?

    nevermind, found it along with a bunch of other gsxr manuals, www.servicemanualsgsxr.com
  12. G

    Where did the gen 2 shop manual go?

    no, just last week it was a sticky at the top of the gen 2 forum, all I did was click it and it opened up the gen 2 manual, it was that easy.
  13. G

    Where did the gen 2 shop manual go?

    Need help finding the shop manual that use to be a sticky.
  14. G

    Need some help please

    I have an 08' with 7700 miles on it and I am having an handling issue. Have had the problem for about 1000 miles now and after one visit to the dealer and one to a local shop, they all seem to cant find anything wrong. The issue I have is that the front end while riding feels like it wants to...
  15. G

    Factory Pro Evo Shift Star Kit Installed

    I installed this kit this weekend and the results were amazing. I think I fell in love with my bike all over again. Install was about 2hrs and very simple. Now every shift feels so effortless and positve. I compare it to like what a short throw shifter does for a car. Like others have said, it...
Back
Top