Recent content by OZBooster

  1. OZBooster

    10.0-1 Air Fuel All Of A Sudden?

    Try unplugging the ams, boostfuel is a multiplication of the tps based on pressure, so whatever effects the tps also plays with boostfuel
  2. OZBooster

    Aem Fail Safe

    Yellow /blue stripe for tach rpm wire
  3. OZBooster

    Turbo ignition map

    116 race fuel , E85 and methanol at various times, was trying E85 with the vipec on the busa Factory busa map is pretty close to real deg advance, logging with editor or woolich can compare ign degrees to what you see on the tables and see just what is going on with corrections
  4. OZBooster

    Turbo ignition map

    Have the Vipec version of the Link now since the previous setup was lost in the fire , running great again on the 750, the busa was giving me fits and i went back to editor gen 2 for the last meeting , but will be going to the Vipec again , its something specific to the bike or my ecu setup ...
  5. OZBooster

    Plenum

    I fit it to my gen 2 plenums and let the idle control function as normal , Frank i assume when you cap it you do the idle control manually ?
  6. OZBooster

    Milky/foamy Oil

    Water in oil can also come from the freeze plugs in head, or water pump Oil looks pretty good considering the clutch cover look , any chance you got a small amount of water in when washing or during the headstud conversion ?
  7. OZBooster

    Oil Sludge In The Radiator And Hoses (solved)

    servicable o rings in the cooler ?
  8. OZBooster

    Help With A Ferrari/busa Build?

    Check the bottom end studs for clearance in the lower case holes, you may have to oversize the holes to get a contact free fit , if they perch the cases across even a little bit when tensioned you will eventually damage the bearings and crank
  9. OZBooster

    Begi Shimless Fmu

    The wastegate mount angle will not help , i had one come here with steeper angle than that that made boost with the wastegate removed porting the turbo may help, cut in and radius the upper edge and knife edge the lower so the exhaust gets turned otherwise the speed of the exhaust gasses dont...
  10. OZBooster

    Begi Shimless Fmu

    Did you log boost pressure or read a gauge , any chance at boost creep ? , dyno graph will show torque leveling or dropping slowly after 8500rpm , it should drop off reasonably quickly is your fuel pressure gauge accurate ?, fluid filled ? not getting buzzed by vibration base fuel at 43psi...
  11. OZBooster

    Lsr Busa Build

    Check the clearance of that fender under full suspension compression, , last thing you want out there is to loose steering control hard braking
  12. OZBooster

    Ecu Editor And 2 Step With Boosted Setup Question

    You will have to ignor the A/F while on 2 step , when you cut the fuel or injector the cyl pumps air which will give a lean reading you should only use the a/f readings whileidle, cruising or accelerating even a failing spark plug will give an innacurate reading , if you think the motor...
  13. OZBooster

    Hard Fuel Rev/cut And Secondary Injectors Controller On Boosted Application

    You can complete the starter circuit without the clutch switch, but have to remove the ecu reference to the clutch switch on gen 2 i think its more than 1 reference, how good are you with wiring diagrams ? if you search online there is a color version of the wiring diagram for buggys
  14. OZBooster

    Rcc Install Instructions

    I have seen some modified to have the base spring pressure adjustable there would be a lock nutted bolt or thread in the middle acting on a plate that the spring seated on , you would see the plate just inside the cover through the centre hole you can plug either hole if this feature is not...
  15. OZBooster

    The Parts Needed After Buying A Turbo Kit ?

    "here is no way the engine is going to empty four quarts of oil out of the sump!" Frank i have logs of extended high rpm running on the salt lakes dropping oil pressure , due to i think windage on crank and gearbox and head filling, improved it in my case by adding capacity and improving...
Back
Top