Recent content by OB_RICO

  1. O

    Anyone else having the same problem

    Thanks all. All screens have been done every last one clean as a whistle. Idle set high,stops that on/off you get from injected engines. Cables set up with no/very little play I like it to be instant no slack. It feels like its not getting fuel or its not being told to add feul or be it with a...
  2. O

    Anyone else having the same problem

    Did the screens. tank,pump,injecters, still no good.
  3. O

    Anyone else having the same problem

    Doing it this week.I`ll let you know if it works. thanks anyway. viol8r on L.A Busa`s found it [This message has been edited by RICO (edited 07 August 2000).]
  4. O

    Anyone else having the same problem

    Thanks J.C Its an RX sold to me as new just before 00 came out,It came with the cam chain mod already done,I assume it is a late 99. Not looked at the filters yet,Please tell how many and where.
  5. O

    Anyone else having the same problem

    Tip it in, Roll it through, Bring the power up a little ready to blast it out and s**t, The engine hesitates, you have to stand it up and wait a few seconds and then it gains power back. Anyone have a fix. This is the set-up. 1) Tick over is set 1250 2) Full standard pipe happens every so...
  6. O

    Has anyone tried the Bridgestone BT-56SS

    I`ve used BT56SS it`s good for grip good on turning in. Looks like it`s going to last a little longer too.
  7. O

    ok now please post where you live.

    Hull,North East England,UK
  8. O

    RICO in Hull

    Out and about round Gainsborough last wednesday night loads of bikes! Do you know of a meet in that area? if so email me paul@blackbirdxx.freeserve.co.uk. We go to sherburn-in-elmet most wed nights,would be good to visit south side and perhaps meet up. Even better would be a group get together...
  9. O

    UK Busa owners ?

    Eurodat, Looks like I`m the nearest to you! Live in HULL work in Scunny,gainsborough,Retford, I`m up and down A15 all the time. BTW 99w BS
  10. O

    Need info on fitting a Quickshifter

    Have two threads running and i`m getting mixed up.
  11. O

    Holeshot Power Shifter

    THE MOTORHEAD Good to see your up for it had faith in you all along. My instructions say cut the feed +ve to the coil or coils max two coils or in the case of four plug cap coils find a wire that is common to all. The switching divice is then wired in-line to break the curcuit.
  12. O

    Holeshot Power Shifter

    THE MOTORHEAD,TURBO 1300,GASABUSA. This has to be one of the most interesting threads on the board,very informative,real world stuff. With this amount of knowledge one of you must know how to kill the ignition. So far Johnny Cheese has left you all standing and hes miles in front, sent me a...
  13. O

    Need info on fitting a Quickshifter

    J.C The diagram is great,real clear. Looks like the O/W wire to the engine stop switch may be the one to interrupt.Any ideas? Thanks.
  14. O

    Holeshot Power Shifter

    Just having a little fun no ill will intended. :biggrin: :biggrin: Had the meter on the o/w wire and right,its a main feed for fuel pump ect. Looking at the diagram sent by J.C.I think i`ve sorted it out. The four greys supply +12 to the plug cap coils they take power FROM the o/w. So if I...
  15. O

    Need info on fitting a Quickshifter

    Simple question? 1)Which wire kills the ignition coils. Found the four multi coloured +ve wires.have traced the 4 greys back to an orange on the left hand side, 2)Is this the ground wire. 3)what is the device it connects to. If you can answer all of the above then I will gladly flash my ***...
Back
Top