Recent content by hayabusa8878

I have a pc 2. I know the bike has the stage 1 download, but have changed the face plate low mid and high. Do not remember where the settings were, and was burning rich. I should have a dyno person tune her? How do I go about finding someone who can do this? And should they have the software, I...

Notice seepage from the valve cover gasket on the right front corner near the cam shaft tensioner area. Do I need just need to tighten the the corner area more? Or should I take the cover off. Seems like a rubber gasket, and does it need that special sealant around the areas of the cam areas on...

When inspecting my water pump I noticed some oil leaking from that area. In the manual it stated to check that area for any leaking. Now I will replace the seals. If anyone has done this job tell me, I have to have the shop install a couple of the seals with their special tools. Is there a kit I...

I have bike lowered with dog bones to the second level, or the middle level. And have the 60" swing arm on her. She hits the stock fender when I hit big bumps. I have noticed other under tail kits. But really have not cared for many of them. Wondering where I could get some information on my...

I have a stage 1 race motor from Carpenter Race Motors. A 1363. With a Full T-Force pipe on her. Sure the emissions are gone, pair valves. When I rev up the motor and hold the throttle just heat comes out of the pipe around 5-7 grand. Even under heavy load going down the road no one behind me...

I changed the oil on my bike recently. And ran it for a couple hundred miles. It has the 1363 motor. I had a hard time telling what was level when checking the oil by myself. I had a friend sit on the bike and hold it level. It was off from the window of oil. So I added more oil. It was down...

you know I think you right I have checked with a couple of people and I will really look at that area. I did notice some coming from that area as well

I have a Carpenter engine out of NJ. A 1363 to be exact. We do get along at this point, instead of me eating a spoon full of ****. Does anyone know where I can get a 1363 head gasket. I see a little oil near cam chain. Big bore kit?

Noticed a area where oil is coming out near the cam chain tensioner area on the head. It had a full motor job done on her. I am having the second recall done on the 99 Busa. If I ask Suzuki while they are there doing the recall on the cam chain tensioner, how much would I expect to pay to have...

I am having the bike looked at on May 2nd. Also I found that when they bike heats up ***** to start, after riding a bit. But let the bike sit 10 minutes or so, and bang she will start right up. I will have them check the grounds on it as well.

Having trouble with the battery. Battery is only a couple of years old. Brought the battery to Batteries plus after I put a full charge on it. They put it through a test, and said they stated it did well on it. I brought the bike to them, and they tested the battery when the bike was running...

Asked some questions about the power commander already. But trying to adjust the low med and high on the face plate of the unit itself. Does the bike have to be running to adjust these items and have it stay to memory? Tried to adjust it when the bike was not running, but the power on the bike...

I have a PC3 It is totally down on the rich bar at idle. Not familiar with the system. Came with the bike, so wondering how to adjust the system. I has the high medium and low set up. When I rev it some smoke is coming out. I think it is fuel? I pulled the plugs, and they were burning white...

still can not find any wire clips at dealer or online yet on the bike. The ones that are black, and you can bend to let go of the wire. If anyone can help please send me some info thanks

There are wire clips on the bike that attach to bolts and have a black rubber on the clip where it holds wires. The one i am looking for is the one that holds the wires to the oil sensor on the cam chain cover area, near the clutch cover. Went to my Suzuki guy and he had no idea where find them...