Dyno Results 2003 Busa

arthur39 · #1 (**permalink**) 11-04-2009, 08:40 PM

I had this tuned over the weekend. Thanks to Tom Miceli, the dyno was a Factory-Pro EC997 eddy-current low-inertia dynamometer with SAE corrections. Mods being Fully Muzzy Titanium, air box mod with BMC Filter 16/41 gearing. I had the ECU flashed by Mr. Smith with unified ignition and fuel maps with all short stacks (ECU editor by Petrik). I synched the throttle bodies before tune with smoothed it out a bit as well. I took a gamble with all short stacks and it paid off. The power commander became handy here for final tuning because we were able to build an advanced map and apply fuel to each cylinder seperately. The picture shows how much Tom was able to gain with the tune. First run was 161 and 102 torque, Final was 177.63 and 106.61 ft/lbs. I tote the bike all over and the power band is smoothe from idle on up. Guess I'll keep the busa

busaville · #2 (**permalink**) 11-04-2009, 11:14 PM

dadofthree · #3 (**permalink**) 11-05-2009, 12:50 AM

bisquit61 · #4 (**permalink**) 11-05-2009, 10:02 PM

expat1970 · #5 (**permalink**) 11-05-2009, 10:07 PM

luccaRSA · #6 (**permalink**) 11-06-2009, 05:15 AM

trekfuel · #7 (**permalink**) 11-06-2009, 06:19 AM

nice results.

Commuta_Busa · #8 (**permalink**) 11-06-2009, 09:11 AM

Tommy is a great guy and has a wealth of knowledge.

Back-again-Busa · #9 (**permalink**) 11-07-2009, 08:06 PM

Arthur mind telling where ya had it dynoed and what the goin charge there is ?
I used to race with Tommy

By the way great #'s

arthur39 · #10 (**permalink**) 11-07-2009, 10:07 PM

sure no problem, he is at Xtreme Machines located in Millstone New Jersey, the cost was $300

piratediverjefff · #11 (**permalink**) 11-08-2009, 07:38 AM

Back-again-Busa · #12 (**permalink**) 11-09-2009, 11:38 AM

Cool ,i didnt know he was working there < been out of the seen to long!
Thanks for the info

Commuta_Busa · #13 (**permalink**) 11-09-2009, 11:41 AM

He only comes in there for the dyno tunning. It's a P/T gig.

Quote:

Originally Posted by Back-again-Busa

Cool ,i didnt know he was working there < been out of the seen to long!
Thanks for the info

KvHotDog4 · #14 (**permalink**) 11-09-2009, 11:53 AM

Quote:

Originally Posted by arthur39

I had the ECU flashed by Mr. Smith with unified ignition and fuel maps with all short stacks (ECU editor by Petrik).

What is this......sounds like something thats needed. Mine is a 2007 when I had it dynoed it was only 149hp. Mods TRE, air filter and down 1 up 3. Since then I also have the full muzzy and power commander but I took the gear back to factory for gas milage I have not had a chance to dyno it with new stuff.

Destin07 · #15 (**permalink**) 11-09-2009, 01:34 PM

Congrats I'm sure its running better than ever

luccaRSA · #16 (**permalink**) 11-10-2009, 04:11 AM

Here is mine. Just wanna compare it, but first I have to convert yours to metric

. This was done month ago at 1800m above sea.
Stock engine, no PC, redesigned exhaust, no GIPro.
In your opinion, are those good results or average.

Thread Tools
Show Printable Version Email this Page
Display Modes
Linear Mode Switch to Hybrid Mode Switch to Threaded Mode

Similar Threads
Thread	Thread Starter	Forum	Replies	Last Post
My Busa's Dyno Results	Cecil_Stringer	Turbo	62	12-07-2005 05:08 AM
2003 R1 Dyno Results from 25 May 05	RamminBusa	Random Thoughts	10	06-02-2005 12:36 PM
2003/2004 Test Results are in......	ks-waterbug	General Bike Related Topics	0	09-24-2003 06:40 AM
dyno results of airbox mod and pc2 on stock busa	OB_THE MOTORHEAD	General Discussion	8	04-09-2000 03:24 PM
Dyno results for \'99 \'busa	OB_Dirty Pete	General Discussion	6	02-10-2000 02:00 PM